Pipe Shoe
Pipe Shoe for Pipe Support Arrangements
A pipe shoe is a component used within a pipe-support arrangement. Its role in an installation is considered alongside the pipe, the support layout, and the requirements of the application. When selecting this pipe shoe, start with the intended pipe size and the relevant design conditions, then review the material, finish, slide plate choice, and any dimensional modifications required for the project. These details help buyers communicate the intended configuration clearly and ensure that the selected product can be reviewed against the operating conditions of the line.
The product is made from carbon steel and is available with a painted or hot dipped galvanized finish. Options are available upon request for modifications to dimensions A, B, C, and D, as well as for the slide plate material. The stated slide plate choices are PTFE, 25% glass filled, or graphite. Because allowable vertical load depends on pipe pressure and wall thickness, selection should be considered in the context of those specific pipe conditions rather than from the product description alone.
The listed options make it possible to discuss the configuration in relation to project needs without assuming that every installation uses the same dimensions or slide plate material. For procurement and technical review, provide the required pipe size and identify the requested finish and plate material. If the project calls for changes to dimensions A through D, include those requirements in the inquiry so they can be reviewed as part of the requested configuration.
Materials, Finish, and Slide Plate Options
Material: Carbon steel.
Finish: Painted or hot dipped galvanized. Specify the required finish when ordering so the requested product finish is clear in the purchase details. Finish selection should be coordinated with the project requirements and the conditions in which the pipe-support arrangement will be used.
Slide plate material: PTFE, 25% glass filled, or graphite options are available upon request. The choice should be stated with the order information and reviewed for suitability in the intended application. Where a graphite slide plate is specified, the bonding or bolting requirement also needs to be identified according to the service temperature guidance provided for this product.
Graphite plate construction: Graphite slide plates are usually bonded. For high temperature service above 500°F, specify bolted construction. This distinction is important when preparing an order for a high temperature application: clearly identify the graphite plate and request bolted construction where the stated temperature condition applies. Do not assume that the usual bonded construction meets that requirement.
Allowable vertical loads: Allowable vertical loads depend upon the pipe pressure and wall thickness. These dependencies mean that load suitability should be evaluated using the pipe’s applicable design information. No single allowable load is stated here, so project teams should provide the relevant pressure and wall-thickness details for technical review rather than relying on an assumed value.
End plates: End plates are provided for pipe sizes 3″ and above. Confirm the pipe size during selection and ordering so this product detail is understood as part of the required configuration.
Ordering, Project Coordination, and Upkeep
When placing an order, specify the figure number, pipe size, description, type, quantity, finish, and slide plate material. Including each requested item helps distinguish the required configuration and supports clear communication between the purchaser, engineering team, and supplier. If modifications to dimensions A, B, C, or D are needed, request them when discussing the order. Any request for a slide plate material or graphite construction should also be stated explicitly.
For application planning, use the pipe’s pressure and wall thickness when evaluating allowable vertical loads. Coordinate those details with the pipe-support design, and confirm the selected pipe size, finish, and plate material against the project requirements. For high temperature service above 500°F with graphite slide plates, specify bolted construction. These checks help avoid ambiguity during product selection and make the requested arrangement easier to verify before procurement and installation.
During installation and ongoing maintenance, review the pipe shoe and its associated support components as part of the site’s established inspection and maintenance procedures. Check that the supplied configuration matches the approved order, including the requested finish, slide plate material, and any dimensional modifications. Where service conditions or project requirements change, reassess the selection with the appropriate technical information, particularly the pressure and wall thickness that affect allowable vertical load. This general coordination approach helps keep product records useful for future inspections, replacement planning, and procurement without assuming a maintenance interval or performance value not specified for this product.
The product image below accompanies the specification information. For a complete quotation or order review, provide the required figure number and the full set of ordering details, along with any relevant project conditions that affect material, finish, dimensional options, load evaluation, or graphite plate construction.