Hot Pipe Support Shoe

The Hot Pipe Support Shoe is specified for pipe sizes from 1/2″ to 6″ NPS and is offered in galvanized or hot-dip galvanized (HDG) carbon steel. Its stated temperature range is ambient to 1200 degrees F, and the specified insulation is high-density calcium silicate. These product details provide a starting point for selecting a support shoe for a hot-pipe application and coordinating it with the pipe size, insulation thickness, and required shoe length.

A pipe support shoe is used as part of a pipe support arrangement. When selecting this product, consider the pipe size and insulation requirements together, rather than choosing by pipe size alone. The product information also directs users to the layering charts for layering-system details. Consulting those charts helps keep the selection aligned with the intended insulation layering for the installation.

• 

Product Specifications

Use the specifications below when checking whether the Hot Pipe Support Shoe is suitable for a project. The listed range and material options describe the product information provided; confirm the intended application and insulation arrangement as part of the selection process.

• Pipe size: 1/2″ to 6″ NPS.
• Material: Galvanized or HDG carbon steel.
• Insulation: High-density calcium silicate.
• Temperature range: Ambient to 1200 degrees F.
• Layering system: See layering charts.
• Standard shoe lengths: 12″ and 18″.

The material choice and the insulation details are important considerations when planning a hot-pipe support. The stated temperature range communicates the listed operating range for the product, while the insulation specification identifies high-density calcium silicate. Refer to the layering charts for guidance on layering-system requirements; do not assume a layering arrangement from pipe size or shoe length alone.

Selection and Application

For practical selection, begin by identifying the pipe size in NPS and confirming that it falls within the listed range of 1/2″ to 6″. Next, establish the insulation thickness required for the installation and consult the layering charts for the applicable layering information. The shoe length should also be selected to match the project requirement; standard lengths are available in 12″ and 18″.

Coordinating these details before ordering supports clearer communication between purchasing, engineering, and installation teams. It gives each team a common set of product-selection inputs: pipe size, insulation thickness, layering information, and length. This is particularly useful when several pipe sizes or insulation arrangements are being reviewed, because the required configuration can be recorded consistently instead of relying on an incomplete description.

The galvanized or HDG carbon steel material options and the stated temperature range are part of the product specification and should be considered in relation to the intended service. The listing does not provide additional project-specific design values, so confirm any application requirements that are not covered by the listed specifications. Matching the ordered shoe to the actual pipe size, insulation thickness, and selected length helps the support arrangement reflect the planned installation.

During project preparation and maintenance planning, keep the product selection details with the relevant piping documentation. Recording the selected material option, pipe size, insulation thickness, shoe length, and applicable layering-chart reference can make later identification and replacement planning more straightforward. This approach keeps the product information connected to the installation without relying on unlisted dimensions or assumptions.

Ordering Information

To order, specify the pipe size, insulation thickness, and required length. The product ordering format is shown as (hs-2010)-nps-thk.-l. Provide the selection details accurately so the requested shoe can be identified against the intended pipe and insulation arrangement. Where a layering system applies, refer to the layering charts as directed in the specification information.

Before submitting an order, check that the requested pipe size is within the stated 1/2″ to 6″ NPS range and that the specified length reflects the project requirement, including whether a standard 12″ or 18″ shoe is required. Include the insulation thickness in the order details, and consult the relevant layering chart rather than substituting an assumed value. These steps help reduce ambiguity during quotation, purchasing, and installation coordination.

The accompanying product image is provided for visual reference. For a complete order description, use the written specifications and the ordering information together: galvanized or HDG carbon steel, high-density calcium silicate insulation, the listed ambient-to-1200-degrees-F temperature range, the applicable layering-chart reference, and the requested shoe length. Confirm project-specific requirements with the responsible design or procurement team whenever they extend beyond the information stated here.